Loading... Please wait...

Top Selling Electronic Cigarettes

                                           How to use the MVP body?

As an upgrade of the original iTaste MVP, iTaste MVP V2.0 has substantial improvements in both appearance and function:

itaste-mvp-body-1.jpg

Vaping Button Highlights 

 

The high lights of vaping button make it responsive and more convenient to operate. 

NewCarbon Fiber Color 

iTaste MVP V2.0 are made of the Zinc alloy and aluminium alloy. Being given special treatment of anodic

oxidation and chrome-plating, the iTaste MVP V2.0 has well display the effect of fibre-drawing,

which make it more quality feel and hand feel. 

Blue Display Color 

The color of the display has been changed from red to blue, giving it more soft feel. 

NewVariableWattage Function. 

iTaste MVP V2.0 has added variable wattage function. The adjusting button applies one way increasing,

displaying the voltage or wattage in a circular way. 

Ohm meter 

The iTaste V2.0 has added the ohm meter. It will display resistance of the attached atomizer, then it

willdisplay the current voltage after 2 seconds. ITaste MVP is a microprocessor controlled VV/VW

personal vaporizer that lets you easily adjust the voltage and wattage with just a few button presses. 

 

 

Ohms meter : 

Reads resistance of your atomizer/cartomizer/clearomizer. 

Puff Counter: 

Puff counter will record the number of puffs you have taken. Either press “P “button  or “U” button 1

second to check puffs ,The Puff Counter will be cleared when the device is turned off. 

Short Circuit/Atomizer Protection: 

Short Circuit/Atomizer Protection protects the iTaste MVP against shorted atomizers. 

Over-Discharge Protection: 

The iTaste MVP monitors the battery voltage and will automatically turn off when the battery is

discharged. 

Battery Level Indicator: 

The iTaste MVP battery capacity is displayed via green, yellow and red LED lights. 

Green = Fully Charged 

Yellow = Half Discharged 

Red = In need of charging 

Large battery capacity: 

iTaste MVP e-cigarette built-in 2600 mAh polymer Li-Ion rechargeable battery. High compatibility 510

connector: Thread fit iClear10,iClear16 ,iClear30 etc 

ON/OFF battery switch: 

Quickly clicking three times will enable or disable the battery. Once enabled, holding down the button

will activate the battery. This safety feature prevents the atomizer from turning on while it's in your

pocket or bag and it prevents any settings from getting changed without you knowing. 

10 seconds cutoff: 

If the button is held down for 10 seconds or longer, the iTaste MVP will shut itself off until the button is

released and pressed again. 

Passthrough: 

The iTaste MVP uses a built in Micro USB Port. You can recharge it with a Micro USB cable. It can also

work as a pass-through for use while charging. 

Remembers last set voltage or wattage : 

Remembers last set voltage or wattage when the battery is turned off and then back on. 

Built-in 3 digit display : 

Digital display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the

battery was turned off. 

Portable power source for electronic products 

Turn ON the small pin switch in bottom of iTaste MVP , connect cable into USB  OUT PUT port(DC 5V ,

maximum output current 0.5A ,the 3 most popular power connectors for

iPhone/iPods, MiniUSB(Motorola/Blackberry), a Micro USB (Motorola/Nokia/LG/Samsung). Turn OFF the

small pin switch when finish charged your electronics . 

OPERATION GUIDE 

There are three main buttons on the iTaste MVP: “ ” button, "P" button and "U" button; all the functions

can be activated by using those three buttons to change settings in a single step, without the use of a

menu system. Your chosen mode will be  displayed on the digital screen. 

“P” button: VW 

“U” button: VV 

ON/Off: 

Quickly clicking the Image button three times will enable or disable the battery. Once  enabled, holding

down the button will activate the battery. 

Variable VoltageMode : Press the “U“ button for 3 seconds to enter variable voltage mode. The screen

will show you the Puff counter first followed by the last adjustment (The last adjustment  may be a

voltage or wattage setting), after showing the last adjustment, the iTaste MVP will enter variable

voltage mode. Voltage can be adjusted from 3.3 to 5.0 volts  in .1 volt increments by pressing

the “U” button. 

VariableWattage Mode : 

Press the “P“ button for 3 seconds to enter variable wattage mode. The screen will show you the Puff

counter first followed by the last adjustment (The last adjustment may be a voltage or wattage

setting), after showing the last adjustment, the iTaste MVP will enter variable wattage mode. Wattage

can be adjusted from 6.0 to 11 watts in .5 watt increments by pressing the “P” button. 

Ohms Meter & Battery Level Indicator & Puff Counter: 

Hold both the “P” and “U“ buttons simultaneously for 2 seconds. The screen will show a series of

readings, the first being the resistance of the attached load ( Rx.x , for example R2.2), the second being

the battery voltage, the third being the number of puffs since the device was last turned off and the

fourth being the last set voltage or wattage. If no load is attached the display with show “NON”. If you

wish to check the number of puffs taken since the iTaste MVP was last turned off, you can also hold

either the “P” or the “U“ button to display the Puff Counter which will be followed by the display of

current mode (VV mode or VW mode). In this state, you can also adjust the voltage or wattage by

pressing the “P” or “U“ button. 

LED Light BlinkingMode: 

The LED light will blink in different colors to indicate the current battery voltage 

1. Red LED light = battery voltage is lower than 3.61V 

2. Yellow LED light = battery voltage between 3.61V and 3.75V 

3. Green LED light = battery voltage is more than 3.75 V 

4. Red LED will keep blinking for 8 seconds when battery capacity is lower than 3.3V and the device will turn off automatically. 

5. Red LED light will stay on for 5 seconds when a load short circuit is detected or the current of the coil

is more than 3.5A, then no vapor will be produced. 

6. If you take a drag for longer 10 seconds, the battery will stop it’s output, the RED light will blink 10

times, and the iTaste MVP won’t continue to work until you press the power button again.